Building codes require an outdoor air supply to help control indoor air quality with the outdoor air representing a significant portion of total HVAC building load. An ERV recycles energy from the normally exhausted building air to pre-condition incoming ventilation air.  By recycling energy contained in the exhaust air, ERVs lower total HVAC energy usage. This is illustrated in Figure 1 below. This process is commonly referred to as load shifting. Shifting the outdoor air ventilation load to the ERV reduces the energy demand on traditional HVAC equipment, allowing the now smaller ERV-based HVAC equipment to operate more efficiently.

Passive Energy recovery relies on the temperature and humidity difference of the two opposing air streams to perform the energy exchange. The larger the difference, the more results the ERV will provide. This trait allows energy recovery components to reduce energy consumption on days that are the hottest, coldest, and most humid. As shown in Figure 2 below, reducing energy demand allows for a more energy efficient system year round for the majority of U.S. climate zones.

While Figure 1 illustrates a wheel and Figure 2 illustrates a plate exchanger, these Figures are intended to apply to all technologies. ERVs are sometimes referred to as air-to-air heat exchangers (AAHX) as in Figure 3 below, which illustrates a generic configuration.

The primary benefit in applying an ERV is the heating, cooling, and humidification ventilation load reductions throughout the year. Paybacks and load reductions can be calculated based on AHRI certified and verified rating points listed below. Performance data based on heating and cooling conditions include:

• Sensible effectiveness at 100 & 75 percent of the rated airflow
• Latent effectiveness at 100 & 75 percent of the rated airflow
• Total effectiveness at 100 & 75 percent of the rated airflow

Performance data measured at room ambient conditions include:

• Pressure drop of exchanger at 100 percent of the rated airflow
• EATR — Exhaust Air Transfer Ratio between the entering exhaust (Figure 3, Station 3) air and the leaving supply air (Figure 3, Station 2) at zero pressure differential
• OACF — Outdoor Air Correction Factor is the entering supply airflow (Figure 3, Station 1) divided by the measured (gross) leaving supply airflow (Figure 3, Station 2) at zero pressure differential
• Purge angle setting (rotary heat exchanger) or Tilt Angle (heat pipe heat exchanger)

In addition to the certified ratings listed, manufacturers have the option to certify EATR and OACF different pressure regimes to provide more detail on how the air-to-air heat exchanger performs under varying pressures. System designers must understand how the air moves between the two air tunnels under varying pressure regimes. Participants have to certify their technology under two of the following pressure differentials:

• -5.00, -3.00, -1.00, -0.50, 0.50, 1.00, 3.00, 5.00 in H₂0
  [-1250, -750, -250, -120, 120, 250, 750, 1250 Pa]

Note: These pressure differentials are between the entering exhaust air (Figure 3, Station 3) and the leaving supply air (Figure 3, Station 2).

As certified effectiveness values typically drive overall operating savings and load reductions, it is important not to overlook EATR and OACF from an operational standpoint.

Effectiveness

The sensible exchange is accomplished by the heat transfer matrix and the latent transfer is accomplished by the addition of a desiccant onto the transfer matrix media. Passive energy recovery relies on the difference in entering conditions of the opposing air streams to perform the exchange. An ERV’s “effectiveness” determines what the leaving condition will be. Effectiveness is further split into both sensible and latent values. A manual selection can be accomplished by using the following equations:

The ventilation load shifting accomplished by energy recovery reduces the capacity required by the chiller and boiler in a central system and that of the DX packaged unit. While it is optional to take advantage of the benefits in the central system, it is mandatory in the DX system to achieve proper control of humidity. If this is not done, the system becomes over-sized and could result in excessive moisture and occupant discomfort.

Exhaust Air Transfer Ratio (EATR)

EATR is defined as the tracer gas concentration difference between the Leaving Supply Airflow (Figure 3, Station 2) and the Entering Supply Airflow (Figure 3, Station 3) divided by the tracer gas concentration difference between the Entering Exhaust Airflow (Figure 3, Station 3) and the Entering Supply Airflow (Figure 3, Station 1) at the 100 percent rated airflows, expressed as a percentage.

If a designer is concerned about the contaminants exhausted from the building or using and ERV in a source controlled application, they need to pay particular attention to EATR. For guidance, review ASHRAE Standard 62, section 5 “Air Classification & Recirculation” on maximum EATR levels. It should be noted that if specified outside air volume is being measured at Station 2 (leaving supply airflow, Figure 3), actual outside air volume is not equal if the EATR is greater than zero.

For example:

• Require 1000 cfm (1696 m³/hr) of ventilation air for a given space
• EATR is 5 percent for the ERV under your specified pressure regime. Measured airflow at Station 2 (Figure 3) is 1000 cfm (1699 m³/hr)
• Actual outside air ventilation volume is:
• 1000 cfm (1699 m³/hr)* (1-EATR) = 950 cfm (1614 m³/hr)
• To compensate for EATR, one must increase the volume at Station 2 to 1053 cfm (1789 m³/hr)
• Airflow at Station 2 = Required Airflow for ventilation / (1-EATR)
• Airflow at Station 2 = 1000cfm (1699 m³/hr) / (1-0.05)
• Airflow at Station 2 = 1053 cfm (1789 m³/hr)

Outdoor Air Correction Factor (OACF)

OACF is defined as the entering Supply Airflow (Figure 3, Station 1) divided by the measured (gross) Leaving Supply Airflow (Figure 3, Station 2).

When specifying an ERV, it is highly recommended that the designer pay attention to the OACF, which is an indication of leakage across the heat exchanger. This leakage can occur within the heat exchanger and/or the seals between the supply and exhaust airstreams.

If the OACF is greater than one, the air is leaking from the supply air over to the exhaust air. Depending on fan configuration, it is likely one will end up requiring additional fan energy. If the OACF is less than one, the air is leaking from the exhaust air over to the supply air. The same parameters need to be taken into consideration when dealing with OACF values of less than one. Fans will not necessarily see the scheduled air volumes unless this is taken into consideration.

How should I apply OACF & EATR into my designs?

AHRI Certified manufacturers can provide details on how scheduled air volumes and overall performance are impacted by the certified EATR and OACF values. It is important to understand what the pressure differential is across the heat exchanger so that the correct OACF & EATR factors can be applied. This is why manufacturers offer multiple ratings for various pressure regimes. The AHRI Directory should be consulted for all certified ratings. When applying the technology, consult a manufacturer or representative to ensure that scheduled air volume and brake horsepower requirements are accurate.

Control and Prevent Frost

In cold climates, frost may occur in the exhaust air side of ERV-HRV. Means to avoid frost or removing frost are required to prevent damage to the heat exchanger and/or increase of pressure drop across the heat exchanger.

Some of the methods that can be used for all types of exchangers:

• Exhaust only: When frost is indicated on the component, the intake blower is de-energized for a period of time to allow exhaust air to warm component, melt frost, and drain or evaporate condensate. Alternatively, exhaust-only operation is determined based on outside air temperature to avoid frosting.
• Preheat: For outdoor air preheat, heat is provided in the outdoor air intake to heat the air to a temperature above the exchanger frost threshold before it enters the component. Alternatively, for return air preheat, heat is provided in the return air before it enters the exchanger to prevent frost from forming.
• Re-circulation: When return air or exhaust air re-circulation is used, return air or exhaust air is substituted, in whole or in part, for outside air passing through the exchanger for defrost purposes.
• Bypass: A portion of the outdoor air is bypassed around the exchanger until the frost threshold is avoided.

Using ERV systems is a great approach to achieving LEED certification in a building. Two prerequisites can be covered when modelling and implementing an ERV:

1. LEED Indoor Environmental Quality Prerequisite 1, Minimum Indoor Air Quality Performance with reference to ASHRAE Standard 62.1-2007, Ventilation for Acceptable Indoor Air Quality
2. LEED Energy and Atmosphere Prerequisite 2, Minimum Energy Performance with reference to ASHRAE Standard 90.1-2007, Energy Standard for Buildings Except Low-Rise Residential Buildings

The difference between these two prerequisites is that one requires outside air for ventilation and the other requires that outside air ventilation be managed as efficiently as possible. Energy recovery devices permit HVAC system designers to accomplish both of these intents in an effective manner.

An ERV recovers energy from exhaust air to pre-treat the outside air, which reduces the load the HVAC unit must handle, thereby reducing the required capacity of the mechanical equipment. An ERV will bring in the required outside air for ASHRAE Standard 62.1 while meeting the energy reduction requirements of ASHRAE Standard 90.1. ERV’s are a cost-effective means in reducing energy consumption without reducing indoor environmental quality.

ERVs can also help achieve LEED Indoor Environmental Quality Credit 2, Increased Ventilation, by allowing system designers to increase ventilation air by over 30 percent of ASHRAE Standard 62.1 requirements. Figure 13 below provides a summary of the potential LEED points that can be achieved using ERV technology.

The ERV certification program will complete the transition to software certification by 2021. The AHRI Directory lists the certified products for all ERV participants. The certification program will be transitioning from a point-type program to certifying the operating map. Therefore, starting in 2020, the AHRI ERV Directory will reflect those manufacturers whose selection rating software have been certified. The following metrics are tested and considered AHRI Certified:

• Sensible Effectiveness
• Latent Effectiveness
• Supply Pressure Drop
• Exhaust Pressure Drop
• EATR (Exhaust Air Transfer Ratio)
• OACF (Outside Air Correction Factor)

The Directory is constantly updated and maintained, providing the most up-to-date information possible to engineers and consumers.

To determine whether a product is AHRI certified, simply go to the Directory and select the manufacturer and the associated unit number for the product. If the product is displayed, it is AHRI certified. Users also may search for a specific ERV by model number.

View AHRI Certified ERV products here.

The main standards that are used to evaluate the performance of ERVs are ANSI/AHRI Standard 1060 and 1061, Performance Rating of Air to-Air Heat Exchangers for Energy Recovery Ventilation Equipment, and ASHRAE 84, Method of Testing Air-to-Air Heat/Energy Exchangers.

AHRI Guideline W, Selecting, Sizing, and Specifying Packaged Air-to-Air Energy Recovery Ventilation Equipment, is designed to provide a base understanding of ERV. When a designer first considers using an ERV for a project, the terminology and application of this technology can be daunting. This guideline helps introduce all the terminology and some of the system features that are required to understand the application of the ERV.

There are several pages of terms that the user needs to understand to ensure correct decisions about the ERV (e.g. EATR and net effectiveness).

Guideline W also will teach:

• Different ways ERVs can be integrated into the HVAC system
• What methods are available to keep the ERV from freezing up during operation (this is called frost protection)
• What to consider in balancing the system
• How to utilize an ERV with (or as) an economizer
• Classes of air that can (and cannot) be used with an ERV

Guideline W also gives several examples of ERVs used in various applications, such as classrooms and libraries.

AHRI Guideline V, Calculating the Efficiency of Energy Recovery Ventilation and its Effect on Efficiency and Sizing of Building HVAC Systems, is a more technical tool that provides the calculations necessary to correctly size an ERV and the associated HVAC system. This guideline is intended for the industry, including engineers, installers, contractors, and users. It provides a means for calculating the impact of applied energy recovery equipment on the energy efficiency of the heating, ventilating and air-conditioning system at a single selected operating condition. The guideline is not a rating system for Energy Recovery Ventilation (ERV) Equipment, nor does it provide a means of estimating annual energy use.

Building Performance

The industry understands the need for ventilation in buildings to dilute pollutants and help provide a healthy environment. What has not been well understood nor appreciated is the contribution that ERVs have had to the overall building operation and energy performance. Until recently, energy recovery was required only when the system required greater than 70 percent outdoor air, according to ASHRAE Standard 90.1-2007. However, as of the 2010 version this is no longer the case. An analysis by the ASHRAE Standard 90.1 Committee and the National Laboratory supporting the standard found that energy recovery is cost effective and provides energy savings. Because of this, ERVs are now included in a table within the 2010 version of the ASHRAE 90.1 Standard (Figure 14), which states that each fan system meeting the requirements of the table shall have energy recovery. The zones in the left column of Figure 14 refer to climate zones.

*Reprinted from ASHRAE Standard 90.1-2010 by permission of ASHRAE (www.ashrae.org).

Furthermore, ASHRAE Standard 189.1, Standard for the Design of High-Performance Green Buildings, required energy recovery with 60 percent effectiveness and starting at 10 percent outside air. This is the high performance building standard and does not require a cost effectiveness measure.

In addition, similar requirements are included in the 2012 version of the International Energy Conservation Code (IECC).

ASHRAE Standards 90.1-2010 and 189.1 are vital to the success of ERV in buildings. Different versions of ASHRAE Standard 90.1 have been adopted by different states; information on which version is used in your state can be found at: http://www.energycodes.gov/status-state-energy-code-adoption

AHRI Standard 1060/1061-2012 Performance Rating of Air-to-Air Heat Exchangers for Energy Recovery Ventilation Equipment — AHRI Standard 1060 was established to rate the performance of factory-made air-to-air energy heat exchangers for use in Energy Recovery Ventilation equipment. The standard uses the ASHRAE 84 Method of Testing Air-to-Air Heat Exchangers as the test reference. The ARI standard outlines the performance parameters to be reported in any literature.

Air to Air Energy Recovery Ventilation Equipment — Energy recovery components and packaged energy recovery ventilation which employ Air-to-Air Heat Exchangers to recover energy from exhaust air for the purpose of pre-conditioning outdoor air prior to supplying the conditioned air to the space, either directly or as part of an air-conditioning (to include air heating, air cooling, air circulating, air cleaning, humidifying and dehumidifying) system.

ANSI/ASHRAE Standard 62.1 - 2010 Ventilation for Acceptable Indoor Air Quality — Standard mandating fresh air to be brought into a building.

ANSI/ASHRAE/IESNA Standard 90.1 – 2010 Energy Standard for Buildings Except Low-Rise Residential Buildings — Standard requiring supplemental load to be provided through energy recovery means when building ventilation criteria meets a specified requirement.

ANSI/ASHRAE/USGBC/IES Standard 189.1 – 2011 Standard for the Design of High-Performance Green Buildings — Standard setting minimum effectiveness levels for energy transfer when using a recovery device.

Delta-P — The pressure drop as measured across an ERV component.

Desiccant — A Hygroscopic substance employed in energy recovery wheels to transfer moisture between opposing air streams. Desiccants are commonly chosen for their adsorption capability and high affinity for water molecules.

Effectiveness — The measure of energy recovery effectiveness not adjusted to account for that portion of the psychometric change in the leaving supply air that is the result of leakage of entering exhaust air rather than the exchange of heat or moisture between the airstreams.

Efficiency — the ratio of the work done or energy developed by a machine, engine, etc., to the energy supplied to it, usually expressed as a percentage.

Energy Recovery Ventilator (ERV) — A ventilator combining a full enthalpic air-to-air heat exchanger which transfers both sensible heat and humidity (latent heat) between airstreams with some combination of fans or blowers to provide fresh air into a building and exhaust air out of a building at minimized cost.

Enthalpy Plate Exchanger — Similar to a static plate technology in construction but the material separating the airstreams promote humidity transfer by using a Hygroscopic resin that allow moisture to permeate the material and transfer to the drier airstream.

Exhaust Air — Building return air that has been passed through the media and to be exhausted from the space.

Exhaust Air Transfer Ratio (EATR) — (%) is composed of carryover leakage resulting from the rotation of the wheel from Return air to Supply air and any seal leakage in that direction, minus the impact of purge. Purge airflow removes return air from the wheel volume before it enters the supply side of the component.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Heat Pipe Heat Exchanger — A device employing tubes charged with a fluid for the purpose of transferring sensible energy from one airstream to another. Heat transfer takes place through the vaporization of the fluid exposed to the warmer airstream and condensation of the fluid in the cooler airstream.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Heat Recovery Ventilator (HRV) — A ventilator combining an air-to-air heat exchanger which transfers sensible heat between air streams with some combination of fans or blowers to provide fresh air into a building and exhaust air out of a building.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Latent Energy — Energy containing humidity.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Net Effectiveness — The measure of energy recovery effectiveness adjusted to account for that portion of the psychometric change in the leaving supply air that is the result of leakage of entering exhaust air rather than the exchange of heat or moisture between the airstreams.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Outdoor Air Correction Factor (OACF) — Outdoor Air Correction Factor is the difference in airflow measured between OA and SA, presented as a ratio. The OACF includes air lost through purge and leakage from the outdoor air stream to the exhaust stream. Accordingly, OACF is used to size the fans.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Outdoor Air — Outdoor air entering the recovery device but not yet tempered by the media.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Plate Heat Exchanger — A device for the purpose of transferring energy (sensible or total) from one airstream to another with no moving parts. This Exchanger may incorporate parallel, cross or counter flow construction or a combination of these to achieve the energy transfer.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Preheat — An additional heat source designed to prevent frost buildup on the ERV while allowing the fresh air to continue being supplied to the building.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Purge — Purge removes exhaust air that would be otherwise carried to the supply air stream by the rotating wheel matrix. Outdoor air is used to clean or purge the wheel matrix before it rotates from the exhaust air stream to the supply air stream. The driving force for the purge stream is the pressure differential between the outdoor air and return air compartments adjacent to the wheel. Purge is accomplished by utilizing the wheel matrix or by mechanical means.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Return Air — Building exhaust air entering the recovery device that has not yet passed through the media.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Rotary Heat Exchanger — A device incorporating a rotating cylinder or wheel for the purpose of transferring energy (sensible or total) from one airstream to the other. It incorporates heat transfer material, a drive mechanism, a casing or frame, and includes any seals which are provided to retard the bypassing and leakage of air from one airstream to the other.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Sensible Energy — Dry bulb energy only without humidity factored in.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Start Stop Jog Function — Economizer mode that eliminates recovery penalty for energy recovery wheels. Accomplished by stopping the recovery wheel and pausing the recovery process when free cooling conditions exist (45 – 65 degrees F). Wheel is momentarily energized to purge wheel of any humidity or particulate matter that has built up on the wheel.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Sensible Plate Exchanger — Static plates use thermal conducting aluminum or synthetic plates to transfer energy from airstreams which are separated by the plate. This promotes sensible energy transfer only as the plate is not porous and therefore does not allow for any mixing off the airstream. This technology is typically applied in drier climates in the far north or in applications where there must be 100% isolation of airstreams.

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Tempered Air — Outdoor air that has been conditioned by the recovery media

Frost Threshold — The outdoor air temperature limit when frosting begin in the exchanger. The frost threshold may vary from exchangers, effectiveness and return air temperature and humidity.

Variable Effectiveness Frost Control (Wheel Speed & Bypass Frost Control) — The process of minimizing exchanger effectiveness by changing rotational speed (wheels) or by bypassing a portion of the air around the exchanger to mitigate frost formation.